See Details

25% Off Online Orders of Select Hard Parts. Enter Promo Code MMJ30 in Cart.

Close (X)

25% Off Select Parts and Accessories
Receive 25% Off Your Online or In-Store Purchase. Use promotional code MMJ25 at checkout to receive discount. Not valid in combination with any other discounts, promotions or items already on sale. Not valid on gift cards, special orders, installed merchandise, commercial or fleet purchases. Those products that are included will be displayed in product search results and product detail pages. INCLUDES the following categories: Starters, Alternators, Fuel Pumps, Radiators, Shocks & Struts, Chassis, CV Axles, Batteries, Ignition, Window Motors, Wipers, Appearance Chemicals, Car Wash Accessories, Floor Mats, Lift Equipment, Hand Tools, Headlamps and Bulbs. Excludes the following brands: Powerstop, Razor, Traxxas, Superchips, Hypertech, Edge, Bully Dog, Diablo, Edelbrock, Holley, NOS, Proform, Specialty Auto, Autometer, Accel, K&N, Kenwood, Pioneer, Sony, Thule, Thule Karrite, JVC, Flowmaster, Hurst, B&M, MSD, Moog, Wagner and BBK Performance. Valid online until 2:59 am EST on 5/1/17.

Free Shipping on Orders Over $50 or in-store pickup
https://www.pepboys.com/customer_care/policies/shipping

200_20_27192
Zoom
×
Zoom [+]
  • Part #: 27192|
  • SKU: 9212095

Available today

Pay in Store Available

    • Heat treated pullers for toughness
    • Rust resistant finish
Retail
$69.99
PayPal available for online purchases. Major credit cards accepted online and in store. Pay online, in-store or take advantage of our Pep Boys credit card. Learn more and see additional details in cart.

OEM Front Hub Puller/Installer

The Front Hub Puller / Installer is used for pulling off front hubs from most front wheel drive vehicles without damaging wheel bearings.
  • Heat treated pullers for toughness
  • Rust resistant finish
  • Comes in a sturdy molded plastic case


9212095

OEM Front Hub Puller/Installer is rated 4.7 out of 5 by 6.
Rated 5 out of 5 by from Worked well I used this tool to replace an axle shaft for a 2007 Ford Focus. The tool worked well.
Date published: 2016-10-28
Rated 5 out of 5 by from Really helpful tool This products is really helpful and really adopted for different types of pyllies
Date published: 2016-10-05
Rated 5 out of 5 by from Made a tough job much easier 1998 Plymouth Grand Voyager, removing the original hub assembly after 18 years. I'd struggled for several hours the day before trying to remove the stuck front hub bearing assembly from the axle, to no avail. The next day I rented this tool, within 15 minutes after I got it home the hub was off. Go slow, use plenty of PB Blaster or equivalent solvent, tap the hub with hammer a few times every quarter turn to help vibrate and loosen things up - that'll help keep from deforming the end of the axle. Once the hub was off I cleaned up the splines and steering knuckle with a wire brush, added a thin coat of grease, and the new hub went on fine with a few light taps of a hammer. Wish I'd just rented this tool from the start instead of fighting the stuck hub for several wasted hours. This tool should work fine most hubs but note it's not designed to be used with air tools.
Date published: 2016-09-12
Rated 3 out of 5 by from only good for putting hubs on this hub puller is basically an incomplete tool. The hub puller presses against the axel bolt, but axels are not solid and you end up pushing the axel in and compressing it. This can damage the axel...Not good. I would recommend using a slide hammer, which USED to include the hub puller. BUT Pepboys decided to make two separate tools and now you'll need to rent BOTH to do the job right. this tool is however goo at putting the hub back on. It's pulls against the axel and pulls the hub back in well...However, Depending on the length of your axel bolt, it may not pull it in enough. I had this issue and I had to use the axel nut to fully push the hub all the way down.
Date published: 2016-07-22
Rated 5 out of 5 by from Effective Did the job effectively on a very difficult to remove wheel hub assembly.
Date published: 2015-06-26
Rated 5 out of 5 by from Rentals saved me a fortune! This is a great program provided by Pep Boys. I purchased rear bearings for my Honda as the dealer was saying cost of replacing bearings would run up to $900. The problem I had was specialized tools to perform the job would cost me a small fortune. Pep Boys had the tools I needed and all I had to give was a deposit. Upon returning the tools I was refunded my deposit. Without this program I couldn't have done the job myself.
Date published: 2014-12-31
  • y_2017, m_3, d_5, h_24
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_6
  • loc_en_US, sid_9212095, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_pepboys