K&N Performance Intake Kit

K&N Performance Intake Kit

  • Part#: 69-6010TR
  • | SKU: 20059607
See all 101 reviews

Available

  • Guaranteed to increase horsepower
  • Designed to improve throttle response and engine sound

K&N Performance Intake Kit

The K&N 69-6010TR Typhoon cold-air intake system is a free-flowing, mandrel-bent aluminum tube air induction system designed to fit some Mazda 3 and Mazda 5 models. The restrictive factory air filter and air intake housing are replaced by the K&N Typhoon cold-air intake which is designed to pull in relatively cooler air and dramatically reduce air flow restriction by smoothing and straightening air flow. This allows your engine to inhale a larger amount of denser air than the factory air intake. More air means more usable power and acceleration throughout the engine's RPM range. The 69-6010TR cold-air intake consists of a black rubber topped K&N high-flow air filter that mounts inside the driver side wheel well directing cooler outside air through free-flowing aluminum tubing into a short ram induction tube that delivers high volumes of clean, colder air into the engine's throttle body for a guaranteed power gain. The intake tubes have an attractive red powder-coat finish that's made to last. The cold-air intake system accommodates the factory mass air sensor and crankcase vent hose. The oversized cone shaped air filter comes with a water repellent DryCharger filter wrap to protect the filter from moisture. The air filter can be used for up to 100,000 miles before servicing is needed depending on driving conditions. This air intake is relatively easy to install usually in 90 minutes or less using existing factory mounting points. The tools needed are a Phillips screwdriver and a ratchet set. Some Typhoon air intakes are not legal for sale or use in California and other states adopting California emission standards while others are CARB exempt and 50 state legal. Check the K&N catalog or website for vehicle applications and specific CARB status for each vehicle and air intake.

  • Guaranteed to increase horsepower
  • Designed to improve throttle response and engine sound
  • Free-flowing aluminum tubes
  • Easy to install, usually in 90 minutes or less
  • Filter lasts up to 100,000 miles before service is required
  • Replaces entire factory air intake system
  • Washable and reusable lifetime air filter
  • K&N Million Mile Limited Warranty
Restrictions
  • WEB ORDER ONLY!


Product Length 18.25
Contains Toluene? No
Is a Remanufactured Part? No
Is a Hazardous Material? No
Product Width 14.5
Product Height 8.5
Estimated Horsepower Gain 5.74 HP @ 4764 RPM
Air Filter Outlet Shape Round
Clamp Material Stainless Steel
Couplers Included 2
Air Filter Color Red
Air Filter Large End Diameter 6 in (152 mm)
Product Box Height 8.5 in (216 mm)
Air Filter Height 5.5 in (140 mm)
Clamps Included 5
Intake Pipe Color / Finish Red
Air Filter Material Cotton Gauze
Clamp Style Regular

20059607

  • Description & Features

    .

    K&N Performance Intake Kit

    The K&N 69-6010TR Typhoon cold-air intake system is a free-flowing, mandrel-bent aluminum tube air induction system designed to fit some Mazda 3 and Mazda 5 models. The restrictive factory air filter and air intake housing are replaced by the K&N Typhoon cold-air intake which is designed to pull in relatively cooler air and dramatically reduce air flow restriction by smoothing and straightening air flow. This allows your engine to inhale a larger amount of denser air than the factory air intake. More air means more usable power and acceleration throughout the engine's RPM range. The 69-6010TR cold-air intake consists of a black rubber topped K&N high-flow air filter that mounts inside the driver side wheel well directing cooler outside air through free-flowing aluminum tubing into a short ram induction tube that delivers high volumes of clean, colder air into the engine's throttle body for a guaranteed power gain. The intake tubes have an attractive red powder-coat finish that's made to last. The cold-air intake system accommodates the factory mass air sensor and crankcase vent hose. The oversized cone shaped air filter comes with a water repellent DryCharger filter wrap to protect the filter from moisture. The air filter can be used for up to 100,000 miles before servicing is needed depending on driving conditions. This air intake is relatively easy to install usually in 90 minutes or less using existing factory mounting points. The tools needed are a Phillips screwdriver and a ratchet set. Some Typhoon air intakes are not legal for sale or use in California and other states adopting California emission standards while others are CARB exempt and 50 state legal. Check the K&N catalog or website for vehicle applications and specific CARB status for each vehicle and air intake.

    • Guaranteed to increase horsepower
    • Designed to improve throttle response and engine sound
    • Free-flowing aluminum tubes
    • Easy to install, usually in 90 minutes or less
    • Filter lasts up to 100,000 miles before service is required
    • Replaces entire factory air intake system
    • Washable and reusable lifetime air filter
    • K&N Million Mile Limited Warranty
    Restrictions
    • WEB ORDER ONLY!


  • Specifications

    .
    Product Length 18.25
    Contains Toluene? No
    Is a Remanufactured Part? No
    Is a Hazardous Material? No
    Product Width 14.5
    Product Height 8.5
    Estimated Horsepower Gain 5.74 HP @ 4764 RPM
    Air Filter Outlet Shape Round
    Clamp Material Stainless Steel
    Couplers Included 2
    Air Filter Color Red
    Air Filter Large End Diameter 6 in (152 mm)
    Product Box Height 8.5 in (216 mm)
    Air Filter Height 5.5 in (140 mm)
    Clamps Included 5
    Intake Pipe Color / Finish Red
    Air Filter Material Cotton Gauze
    Clamp Style Regular
  • Customer Reviews

    .

    20059607

×