Save 30% Off Orders Over $150 or 20% Off Orders Over $100 or 10% Off Orders Over $50
Use promotional code PROMO10 at checkout to receive 10% off orders over $50. Use promotional code PROMO20 at checkout to receive 20% off orders over $100. Use promotional code PROMO30 at checkout to receive 30% off orders over $150. Not valid in combination with any other discounts or promotions. Not valid on tires, special order, wheels, outside purchase or sale products, installed merchandise, commercial, or fleet. Excludes the following brands: Traxxas, Superchips, Hypertech, Edge, Bully Dog, Diablo, Edelbrock, Holley, Autometer, Accel, K&N, MSD and BBK Performance. Valid online until 2:59 am EST on 12/22/14. Online orders scheduled for in-store pick up must be completed in store by closing on 12/21/14 for discount to apply.
Free Shipping Over $50
Free Ground Shipping on Ship to Address orders over $50. Offer only valid on in-stock merchandise valued at a total of $50, after any discounts have been applied, and before any core charges, shipping charges, fees and taxes have been added. Certain items exceeding weight and size limitations are excluded from all shipping promotions and may require additional shipping fees. Please see item descriptions or visit our Shipping Policy page for details.
Oils for new cars have specifications that can be found in the catalog look up. If your car does not have oil specifications, please check your owner's manual for the right type and weight of oil.
Changing your car's oil yourself is not only a money saver; it's also a lot easier than it sounds! When it comes to automotive maintenance, safety always comes first. So whether you're a first timer or an old hand, go through these instructions to ensure you the safest and most efficient way to perform your oil change.What You'll Need
Go to Pep Boys to get every thing you need to change your own oil.
4 to 6 quarts of motor oil, (check your owner's manual for the proper SAE viscosity, API performance and quantity required for your car’s engine.)
Your owner's manual for your vehicle will recommend a weight and type of oil to be used under normal driving conditions as well as the number of miles that you should drive your vehicle before changing your oil, (drain interval). Oil types include Conventional or Synthetic or High Mileage oil for cars with more the 75,000 miles. However, if you drive mostly under severe conditions such as extreme temperatures, frequent short trips, stop and go traffic or towing and hauling, the extra strain on your engine will necessitate more frequent changes.
The average driver generally doesn't realize it but the vast majority of their driving falls into this category, which is why most mechanics will refer to and change oil by the shorter drain interval recommended by the manufacturer for use in "severe" driving conditions.
Check your owner's manual for special conditions and do not exceed warranty recommendations. FOLLOW YOUR VEHICLE MANUFACTURER'S RECOMMENDATIONS ON OIL VISCOSITY GRADE AND TYPE.Step 2 - Prepare Your Vehicle
Always be certain to consult your owner's manual for specific safety precautions before climbing under your vehicle.
On the top of the engine you will find a cap that says "Oil". Unscrew the oil filler cap, this helps quickly and completely drain the oil from the engine.
Never use a bumper jack to hold your vehicle up - it is simply too unstable.
Ramps are ideal and much safer. Wheel ramps will tilt the car just enough to allow you to slide underneath. After making sure that you are on level ground, drive your vehicle up onto the wheel ramps so that the front tires are elevated. Set your emergency brake and brace both rear wheels with wheel chock. Put your vehicle in first gear if you have a manual transmission and in Park if you have an automatic transmission.
Cold oil will not drain properly so idle your engine for about 5-10 minutes to bring it to normal operating temperature (never start your engine without oil). Then switch off the engine and raise the hood to locate and loosen the oil filler cap to avoid creating a vacuum. This will allow the oil to drain from the bottom more freely.Step 3 - Drain the Old Oil
Locate the oil drain plug on the underside of your vehicle. It should be located at the bottom rear end of the engine sump or oil pan. Be sure not to loosen the automatic transmission drain plug by mistake. (It is usually located a bit further back.)
Place the drain pan underneath the drain plug and slightly toward the back. Using your wrench, turn the plug counterclockwise until it rotates freely. Finish removing the plug by hand. At this point, be careful of the oil since it may release rapidly and may be hot. Try not to drop the plug into the pan, but don't worry if you do. Reposition the pan, if necessary, to catch all the dripping oil.Step 4 - Remove the Oil Filter
Next, loosen the oil filter - which may be warm - by turning it counterclockwise with a filter wrench. Complete the removal by hand, taking care not touch the hot exhaust manifold. The oil filter may be filled with oil and feel slightly heavy, so carefully ease it down and away from the engine and tip its contents into the drain pan.Step 5 - Replace the Oil Filter
Take a rag and wipe in and around the filter seat on the engine. Then take a new filter and use your finger to apply a light film of new oil to the gasket, (the circular edge of the filter itself). The oil will act as a sealant.
Now gently screw the new filter onto the threaded oil line, turning it clockwise. If it's aligned properly, the filter should thread on easily. Hand-tighten the filter approximately ½ to ¾ of a turn after the gasket makes contact with the mounting surface. Make sure the filter is mounted snugly, but be gentle, don't over tighten.
Be sure to clean the copper gasket and the oil plug. Use a rag to clean old oil or road dirt from the area on the oil pan near the oil plug hole before re-installing the drain plug. Then align and replace the plug. Screw it in by hand, but finish tightening it with your wrench. Tighten the oil drain plug, don't over tighten the oil drain plug.Step 6 - Add Clean Oil
Use a funnel to pour the new oil into the filler hole on top of the engine (oil spilled onto the engine or exhaust system will stink up the engine; oil spilled onto the exhaust system can even potentially be ignited). Add the recommended number of quarts, from your owner's manual. Check with the dipstick to assure proper fill level. Then replace the oil filler cap and wipe off any spillage.
Once you have the oil level reach the recommended line on the dipstick start the engine. The oil light should go out as soon as the engine is started, if it doesn't, turn off the engine and recheck the oil level on the dipstick. Run the engine for several minutes, then switch it off and check the dipstick once again to assure proper oil level.
Last, but not least, check under the vehicle for leaks. Easier than it sounded, right?Step 7 - Dispose of Your Used Oil
Thought you were finished? Not quite yet! The final, and in some ways, most important step to your oil change, is the proper disposal of the used oil that you have drained from your vehicle. Used motor oil is highly toxic to the environment and it is of important that it is disposed of in a safe fashion. Transfer the used oil to sealed container and return it to any Pep Boys location, we will be glad to take your used motor oil and properly recycle it.